COTS PRODUCTS > COTS DIGITAL / ANALOG PRODUCTS > CARRIER / ADAPTERS PRODUCTS > AT-PCI-PMC-Adapter
 
Half-length PCI card
Adapts a single-width PMC form factor to PCI/X
Support 32/64 bit PCI Bus
Supports both 33Mhz/66Mhz or extended
Four 64-pin PMC connectors
Compliant to IEEE P1386.1 Specifications
Front or rear connection I/O access
Universal 5V or 3.3V PCI Signaling
LED indicators to indicate the Power supplies
No software drivers are required
 

PCI to PMC is an adapter to install a PMC card into a PCI slot. This card is sometimes known as a carrier or converter PCI to PMC. The card is a universal voltage 1/2 length PCI card, and will fit into standard desktop PC environment. The combination of PCI to PMC and mounted PMC will occupy a single PCI slot. Mechanically, a PMC card fits cleanly on a short-length PCI board, resulting in a highly acceptable delivery solution for desktop applications. It is recommended that this adapter be installed in a standard PCI-based system. Designed to host 32/64-bit PMC card, the PCI to PMC adapter requires no special bridge software to integrate PMC Mezzanine cards in to PCI systems. The extender supports 3.3V and 5V PCI bus signaling. The product will work with 33 MHz and 66 MHz clock speeds, and with 32/64-bit bus width. The carrier card acts simply as an adapter to route PCI bus signals to and from the PMC card through the PCI card slot edge connector. All ATs PMC cards and those from other vendors are supported. This board provides an easy and low cost solution that enables use of a PMC mezzanine I/O card in a standard PCI computer system. LED indicatorspresent provide detection of PMC card and the power supplies plugged onto the adapter card.

This card is well suited for enterprise router/switch/gateway providers and system integrators. The PCI Express to XMC adapter allows a single width XMC card to be used in a PCI Express slot. The XMC site is VITA 42.3 compatible and supports a single (X1) PCI Express lane. The adapter is completely transparent to PCI Express. It helps to compensate for poor system signal quality by providing adjustable signal equalization and compensation for the high speed PCI Express signals. The P16 connector breakout provides convenient access to all P16 signals through a 78-pin D-sub connector. 20 pairs of signals from P16 are routed as differential pairs to JDP1 so that high-speed IO standards can be used in the cable. Balance 38 signals are provided as single ended. Using the optional power jack to the adapter card may provide more power to the XMC card. The power jack provides +12V to the adapter and powers an on-board 3.3V@3A and 5V@3A. The XMC card is cooled either with a fan or Conduction-Cooling as per VITA standard 20. The bracket mates to standard PMC end brackets and supports an EMI gasket. All connectors from the XMC end bracket are fully accessible. Applications include custom interfaces to XMC P16 connector & multi-card system synchronization and control. No software is required to operate the adapter.

Standard Usage
Mount the PMC card to the PCI adapter.
Carefully grasp the upper edge of the adapter.
Align the gold striped edge connector with the expansion slot socket.
Press the board firmly into the socket.
Make sure that the metal bracket provided is fixed firmly into the corresponding slot.
Applications
Fast, Simple Expansion
Fast Integration of COTS or Custom I/O
Ultra-high bandwidth to/from daughter boards
Mezzanine Slots
One PMC Slot
32bit, 33 MHz or 66MHz
Size
Half size PCI card
32 bit PCI 2.1 Compliant
PMC Compatibility
PMC compliant as per the IEEE 1386 specification
Interrupts
INTA, B, C, D routed to PCI connector from PMC
VIO
PCI IO Voltage is set by the PCI backplane. VIO is routed from the PCI connector to the PMC
Access Width
Standard PCI byte lanes supported for byte, word and long access dependent on installed PMC
64 or 32 bit operation supported
LEDs & Test Points
Power indicator LEDs
Environmental
Operating Temperature: -40C to +85C
Storage Temperature: -55C to +100C
Relative Humidity: 5% to 95% (non-condensing)
Software
No software required
Warranty
1 year limited warranty
 
CORPORATE   ABOUT   FOLLOW US ON
AdTEC Electronics Inc.
4677 Old Ironsides Drive
Ste 230 Santa Clara
California 95054, USA
 
AdTEC Electronics specializes in providing end-to-end custom product design & development encompassing System, Mechanical, Board Electronics, Chip design, Firmware and Application Software Engineering. Our design capabilities include design for testability and rugged design to meet both commercial and stringent regulations.
 
HOME ABOUT US COTS PRODUCTS SERVICES & SOLUTIONS SUPPORT & RESOURCES NEWS & EVENTS BLOG CONTACT US
AdTEC Electronics Inc.