COTS PRODUCTS > COTS DIGITAL / ANALOG PRODUCTS > CARRIER / ADAPTERS PRODUCTS > AT-VME-PMC-CAR
 
VME PMC Carrier Card - 6U size, single slot
Fully compliant to VME64x standard
Supports 3.3V PCI signaling
Compliant to IEEE P1386.1 Specifications
Board uses 3.3V and 5V derived from Backplane power supply unit
PCI-Bus 64 bit, 33MHz/66MHz
VME A32/A24/A16 Master and Slave Addressing
User I/O Routing
LED indicators to indicate the Power-on condition
Easily configured with any combination of PMC Modules
Combine different interface types and functions on one VME card
 

The ATs VME-PMC-CAR is a single slot, double height (6U) VME64x, extended VMEbus module with two separate PMC slots. The VME-PMC-CAR uses an on board, industry standard, Tundra chip (Tsi148) providing the bridge between the VMEbus and PCIbus. The VME-PMC-CAR fulfils the requirements of the VME64x extension plus the Interface for Rear I/O. Each PMC-slot is in conformance with the Draft Standard Physical and Environmental Layers for PCI Mezzanine Cards (P1386.1). The card comes standard with easy to read front panel configuration displays, and two single width PMC slots. The VME PMC carrier allows the user to build powerful and cost effective VME systems by increasing board density.

The VME-PMC-CAR is designed to plug all standard PMC modules with a maximum PCIbus width of 64bit operating at 66MHz. The VME-PMC-CAR carrier board supports the +3.3V PCIbus signaling, hence only +3.3V tolerant devices may be used.

General
VME64x bus Interface
PCI bus Interface: Fully PCI 2.1 Compliant, 3.3V Signaling
Form Factor: 6U size
PMC slots compliant to IEEE P1386.1 specifications
VME to PCI Bridge
High performance 32bit VME interface
Fully compliant with PCI Standard (Revision 2.1)
VME master and slave capability
PCI master and slave capability
Full VMEbus system controller functionality
PCIbus
Provides the connection between the PMC interfaces to the VMEbus Interface
Fully compliant to PCIbus Specification Rev 2.2
PCIbus width of 64 bit
PCI bus operation of 33MHz/66MHz
PMC Slot
Each PMC slot provides 64bit, 66MHz PCIbus operation
Each PMC slot provides the capability for Rear-I/O (VME64x Mapping)
Front Panel
The Front panel provides two breakouts for using the standard PMC- front panel bezel
Physical
Single VME64x slot
VME 6U form factor 233 mm X 160 mm
Environmental
Temperature Range
  Conduction Cooled Air Cooled
Operating -40C to + 85C 0C to + 60C
Relative Humidity: 5% to 90% (non-condensing)
Input-Output
64 I/O signals of PMC slot 1 routed to VME P0 connector
64 I/O signals of PMC slot 2 are routed to row A and row C of VME P2 connector
Electrical Specification
Board uses 3.3V and 5V derived from Backplane power supply unit
Warranty
1 year limited warranty
 
CORPORATE   ABOUT   FOLLOW US ON
AdTEC Electronics Inc.
4677 Old Ironsides Drive
Ste 230 Santa Clara
California 95054, USA
 
AdTEC Electronics specializes in providing end-to-end custom product design & development encompassing System, Mechanical, Board Electronics, Chip design, Firmware and Application Software Engineering. Our design capabilities include design for testability and rugged design to meet both commercial and stringent regulations.
 
HOME ABOUT US COTS PRODUCTS SERVICES & SOLUTIONS SUPPORT & RESOURCES NEWS & EVENTS BLOG CONTACT US
AdTEC Electronics Inc.