SERVICE & SOLUTIONS > CUSTOM PRODUCT DEVELOPMENT > DIGITAL / ANALOG PRODUCTS > RADAR VIDEO INTERFACE BOARD
  • Features
  • Overview
Built In Test Signal
Video Loop back Test
Selection of any two Radar Videos
Selection of any two IFFr Videos
Selected Signal Filtered for noise rejection and offer Suitable signal processing delivered to the out put Port
Equipped Several link for Command for Reselection
Each Channel Gain and Offset adjustment
Video type LIN/Log/MTI
 

This VME based slave card capable of Interfacing to two External Primary Radar Sources and two External Secondary IFF Sources.

Primary Analog:
Primary Analog video inputs (LIN/LOG/MTI) from the two radar sources shall be adjusted for gain and offset using front panel potentiometers. Then the Primary Video signals shall be scaled down to and given out on VME-P2 connector to the next card in the system.
Secondary Analog:
Secondary Analog Video inputs (IFF) from two radar sources shall be adjusted for gain and offset using front panel potentiometers. Then the Secondary Video signals shall be scaled down to and given out on VME-P2 connector to the next card in the system.
Digital inputs:
Digital inputs from the primary radar sources, namely ACP, SHM and SYNC shall be conditioned by means of protection, pulse discrimination and validation. Then the buffered Digital signals shall be passed out VME-P2 connector.
Video signals and Digital signals shall be fed back to the card after being routed in another associated card of the system. The card shall conduct POST by comparing the looped back signals and the input signals. The card shall also conduct on-line diagnostics by comparing the looped back signals and input signals. Hence, the Card operates in three modes: POST, Normal and On-Line Diagnostic.
Control and software programmability by the host is through VME interface, since this card would be used in a VME back plane in combination with other associated cards.
The RVIF Board is mainly used in Radar Systems for communicating two signals. The board has two channels namely channel 1 and channel 2 for communicating signals with the radar.
On-board features include 1 Megabit (128 K x 8-Bit) Uniform Sector Flash memory, 1K (128x8) SPI Serial EEPROM, In-System Programmable Configuration PROM, High performance Spartan-IIE Xilinx FPGA which has densities ranging from 71,000 to 2,00,000 system gates and System performance is supported beyond 200 MHz, High performance CPLD which has 288 macro cells with 6,400 usable gates and system frequency up to 208 MHz.
ARINC429 Interface
Type II PC Card
16 bit PCMCIA Architecture
DDC Controller
2Tx / 4Rx ARINC429 Channel
128 x 32 bit Static RAM interface
Programmable Interrupts
Configurable Bit Format Control
Built-in Fault Detection Circuitry
Transmit Interface
Programmable 12.5/100KHz bit rate
Two 32 (words deep) x 32 (bit) Transmit FIFO’s
Independent data transmit by each channel
Programmable data transmit rate for each channel
Transmit FIFO Status Indicators
Receive Interface
Four 32 (words deep) x 32 (bit) Receive FIFO’s
Receive data rates can be programmed for channel 0 and 1 independent of channel 2 and 3 in each ARINC429 controller
Reducing Receive Data Latency
Filtering & Sorting of data
Storage of data
Parity Error Checking & Reporting
Receive FIFO status indicator
Diagnostics
Testing of Memory Elements
Testing Transmit/Receive functions
Wraparound Test for each channel
Interrupt Function Testing
Error Conditions
Sequence Error
Address Error
FIFO Overflow Error
Receive Data Parity Error
ARINC Clock Error
Software Support
Driver and high-level API libraries for Windows XP
A powerful 'Virtual Instrument Panel' developed to mimic the physical card features & capabilities for interactive control & monitoring
Sample applications provided
Physical
Type II PC Card
Card dimensions- 54.0 x 85.6 x 5 mm
Environmental
Operating temperature: 0º C to +50º C
Storage temperature: -20º C to +70º C
Power
+ 5 VDC
Warranty
1 year limited warranty
 
CORPORATE   ABOUT   FOLLOW US ON
AdTEC Electronics Inc.
4677 Old Ironsides Drive
Ste 230 Santa Clara
California 95054, USA
 
AdTEC Electronics specializes in providing end-to-end custom product design & development encompassing System, Mechanical, Board Electronics, Chip design, Firmware and Application Software Engineering. Our design capabilities include design for testability and rugged design to meet both commercial and stringent regulations.
 
HOME ABOUT US COTS PRODUCTS SERVICES & SOLUTIONS SUPPORT & RESOURCES NEWS & EVENTS BLOG CONTACT US
AdTEC Electronics Inc.