Single Board Computers- AT-cPCI-SBC

Features
Overview
Product Specifications
Ordering Information
Download Datasheets

	6U HT Single Slot width 6U Compact PCI Form Factor Card
	Compliance to PICMG 2.0 R3.0 compactPCI Specification
	On Card ETX Computer On Module specification:
	> 1.0GHz Ultra Low Voltage Intel Celeron M (Dothan) > Cache - 1MB L2 Cache, FSB - 400 Mhz > Chipset - Intel 855GME/ECH4M > System Controller – PC Compatible DMA and Interrupt controller, timers & Watchdog Timer > DDR SDRAM up to 1GB capacity using SO-DIMM Main Flash - IDE > Compact Flash up to 8 GB > Three USB 2.0 Ports available on back panel Connectors > Six RS422 Channels > One AC’97 Audio Port, One VGA port > PS2 Keyboard and Mouse Interface > ISA and PCI (32 bit/33Mhz) Bus interfaces
	Additional features on the card:
	> Two Dual redundant 1553B Channels programmable as BC/RT/MT > One 10/100BaseT Gigabit Ethernet Port > One USB2.0 port for Auxiliary Flash Disk Interface > One Virtex 4 LX60 FPGA to Handle IO requirements as per ICD > 5V TTL/CMOS Differential Inputs - 16 Nos > 5V TTL/CMOS Differential Outputs - 40 Nos > 8 x 28V/Open Inputs > 8 x 28V/Open or GND/Open Outputs > One 3.125Gbps LVDS channel > Rear IO Connectivity to all the interfaces through Rear IO transition Board > Rugged Version with Heat Sink Metal Plate and Card Wedge Locks > +5V and +3.3V Back Plane supplied Power

The AT-cPCI-SBC-CELERONM is an exceptionally high integration, high performance, rugged and high quality Card that contains all the component subsystems of an ATX motherboard with cPCI Back Plane Interface. This enables it to be used in systems designed around cPCI Architecture. The cPCI card has a Computer on Module ETX802 plugged into it. ETX802 is based on one of the ultra high performance, high-integration Intel Celeron M processors and gives designers the choice of a complete, high performance, rugged, embedded processor based on the ETX form factor that conforms to the ETX V2.7 specification. The module plugs into the card, which has connectors and additional circuitry to meet your application requirements.

CPU

	1.0 GHz Ultra Low Voltage (ULV) Celeron® M 373 (with 512 KB L2 cache) processor
	Front Side Bus (FSB) of 400 MHz

Memory

	Single 200-pin DDR SODIMM socket provided
	Supports a single +2.5V DDR RAM SODIMM up to 1 GB
	Supports PC2700 DDR 333 (166 MHz)

PCI Bus/ISA Bus

	PCI 2.2 compliant (32 bit/33Mhz)
	DISA bus speed at 8 Mhz

IDE Interfaces

	Supports two enhanced IDE controllers (4 devices)
	Supports dual bus master mode
	Supports Ultra DMA 33/66/100 modes
	Supports ATAPI and DVD peripherals
	Supports IDE native and ATA compatibility modes

Serial Ports

	Two buffered TTL serial ports with full handshaking (transceivers on baseboard) provided
	Provides two 16550-equivalent controllers, each with a built-in 16-byte FIFO buffer
	Provides programmable word length, stop bits and parity
	Provides 16-bit programmable baud-rate generator
	Provides full modem capability

RS422 Ports

	Provides for Six RS422 ports connected to user IO connector
	Accessible through Rear IO Transition Board

USB Ports

	Supports two root USB hubs
	Supports four USB ports
	Supports USB v2.0 and legacy v1.1
	Supports over-current fuses on baseboard
	Supports USB Boot and the respective USB Boot devices
	Three USB 2.0 ports made available at the connectors
	One USB 2.0 port for access to compact flash in offline mode

Keyboard/Mouse Interface

Supports PS/2 keyboard & mouse

Audio Interface

	Supports AC’97 standard
	AC’97 CODEC provided on-board
	Audio amplifier provided on the card

Ethernet Interface

	Intel 82551QM Controller and one Ethernet port provided
	Supports magnetic and RJ45 connector on baseboard
	Supports IEEE 802.3 10BaseT/100BaseTX compatible physical layer
	Supports Auto-negotiation for speed and duplex mode
	Supports full duplex or half-duplex mode
	Full-duplex mode uses IEEE 802.3x flow control to transmit and receive frames simultaneously
	Half-duplex mode supports enhance proprietary collision reduction mode
	Intel 82540EP based 10/100/1000 Base TX port
	Both the ports routed to Back Plane User IO Connectors and accessible using Rear IO Transition Board

Video Interfaces (Crt)

	Supports CRT (1600 x 1200) with 64 MB UMA (Unified Memory Architecture)
	Integrated 128-bit graphics controller provided

JTAG

	On-board JTAG chain for FPGA's
	On-board JTAG header for CPLD programming
	On-board JTAG interface to the processor for debugging and development purposes

Miscellaneous

	Real-Time Clock (RTC) with external battery provided
	Supports battery-free boot
	Watchdog Timer feature provided

I/O Interfaces

	40 x TTL Differential o/p channels
	16 x TTL Differential i/p Channels
	8 x 28V/ Open Inputs
	8 x 28V / Open or GND/Open Outputs

LVDS Channel

	One LVDS TX Channel of data rates of up to 1.125 Gbps
	One LVDS RX Channel of data rates of up to 1.125 Gbps
	With combined data rates of up to 3.25Gbps in full Duplex mode
	Provided using external LVDS transceiver interfaced to FPGA

FPGA

	Provides on On-board Virtex 4 LX60 FPGA
	FPGA customizable to handle various digital IOs as per customer LCD
	Interfaced to Processor on North Bridge on PCI Bus

Mechanical

	6U compactPCI card
	Board Dimensions: 160mm x 233mm
	Board thickness: 2.4mm
	Rugged Version with Heat Sink Metal Plate and Card Wedge Locks

Power

	Derived from +5.0V and +3.3V of Back Plane
	All other voltages internally derived
	Power Consumption 20-Watts Approx

Environmental

	Air-Cooled	Conduction-Cooled
Operating temperature	0ºC to +60ºC	-40ºC to +85ºC

Operating Systems Support

VxWorks (Ver 6.3 workbench 2.5) Board Support Package (BSP), Windows CE (Ver 6.0) and Windows XP

Warranty

1 year limited warranty